☰ Menu
ShankCheck › Guides
Find the right presser foot

Original or universal presser foot: which one should you buy?

A foot sold as universal fits only one shank system and only up to a certain stitch width. Simple feet are usually fine as generics. Feet with moving parts or tight tolerances are where the original often pays off. We earn a commission when you buy through our links. That does not change what we recommend.

Find your match →
Editor: Will RieggerIndependently researchedSources linkedNo extra cost to youLast checked: 2026-11-20

As an Amazon Associate we earn from qualifying purchases. This does not change your price.

Four questions before you order any foot

  1. Does your foot screw on or snap on?Look at the foot holder. A screw at the side means screw-on. A lever or notch means snap-on.
  2. What is your shank height?Lower the presser bar and measure from the needle plate to the center of the foot screw. About 1/2 inch (13 mm) is low shank, about 1 inch (25 mm) is high shank. Compare with your manual, because retailers quote slightly different values.
  3. What is your maximum stitch width?Many machines are 5 mm, 7 mm or 9 mm. The foot's needle opening must allow the widest zigzag, or the needle can strike the foot.
  4. Is it a simple foot or one with moving parts?A 1/4 inch foot or zipper foot is a good generic candidate. A walking foot, ruffler or binder is where original quality shows more.

Quick reference

Your machineShank systemUniversal foot OK?Watch out
Most Brother, Janome, Singer, Kenmore and Baby Lock machines with a screw-on foot (check your manual)Low shankYes, for simple feetMatch the max stitch width, 5 mm or 7 mm
Machine with snap-on holderSnap-onUsually, if the holder is standardSome models need an adapter. Check the listing
Quilting or heavy-duty machine, foot sits higherHigh shankYes, if listed as high shankLow shank snap-on feet need a high shank snap-on adapter. For other feet, look for a model-specific adapter from the machine maker
Singer slant needle machineSlant shankOnly slant shank feetSearch with your exact model number
Bernina built before the late 1990sOld styleYes, with #75 old style adapterOld and new style adapters do not swap
Bernina Activa, Artista, Aurora and laterNew styleYes, with #75 new style adapterNew style feet have red numbers on the sticker
Singer FeatherweightLow shankSimple feet, yesCenter needle machine. Check the listing for your exact model

Our picks

Top pick

Brother SA140 walking foot (original)

For: Owners of low shank Brother and Baby Lock machines up to 7 mm who quilt or sew layers.

It is the original part for 7 mm low shank machines. Some Brother PC and ULT models need a low shank adapter, so check your model first. Use it for forward sewing only.

Price range: Roughly $80 for the original at one US retailer (AllBrands lists $79.99). Check current prices. Much cheaper listings are usually generic or third-party versions.

View on AmazonAd

Universal low shank walking foot with quilt guide

For: Quilters on a budget with a standard low shank machine up to 7 mm.

Much cheaper than the original, and listings often claim an SA140 fit. The moving parts are the weak point on cheap versions, so buy from a seller with an easy return.

Price range: Roughly $15 to $40 (our estimate, prices vary)

View on AmazonAd

Bernina #75 low shank adapter

For: Bernina owners who want to use inexpensive screw-on low shank feet.

It lets standard low shank feet work on a Bernina. Buy the old style or new style version that matches your machine, because they do not swap.

Price range: Roughly $15 to $25

View on AmazonAd

Low shank 1/4 inch piecing foot

For: Piecers and quilters with a low shank machine.

A simple one-piece foot with no moving parts. A good generic candidate, as long as the needle opening fits your stitch width.

Price range: Roughly $8 to $25

View on AmazonAd

Snap-on foot set with low shank ankle

For: Beginners who want zipper, cording, hemming and darning feet cheaply.

Sets cover many tasks for little money. Quality varies, so expect to replace one or two feet you use a lot.

Price range: Roughly $12 to $30 (our estimate, prices vary)

View on AmazonAd

High shank snap-on adapter

For: Owners of high shank machines who want to use low shank snap-on feet.

It bridges the extra height to the needle plate, so snap-on feet made for low shank can be used. Confirm your shank height before ordering.

Price range: Price not checked. Compare several sellers.

View on AmazonAd

Our take

We would buy generic for simple feet and original for anything with moving parts. A 1/4 inch foot, a zipper foot or a cording foot is cheap to replace if the generic turns out poor. A walking foot is different. We would pay for the original if you quilt often, and a budget version is a reasonable choice for occasional use if the seller takes returns. On a Bernina, we would buy the right #75 adapter first and use generics for rarely used feet. Whatever you choose, shank type and stitch width decide fit, not the word universal.

What owners report

  • Many users on a sewing forum report that brand walking feet are better built than cheap copies and can often be adjusted and oiled. Some say a few generics performed close to the original on their machine. Source
  • Some Bernina owners report that a generic ruffler worked well enough for occasional use, while the original uses better material. Source
  • Several users report that a foot sold as universal did not fit their machine, and one returned a generic foot that did not fit a Bernina. Source
  • A customer review of a low shank walking foot says it fits a Brother and works as expected, but the automatic needle threader cannot be used with the foot attached. Source

Common buying mistakes

  • Buying by brand name only. Two Brother machines can need different feet, depending on shank and stitch width.
  • Ignoring maximum stitch width. At the widest zigzag the needle can strike a foot with a narrow opening.
  • Mixing up Bernina old style and new style adapters. They are not interchangeable.
  • Putting a low shank foot on a high shank machine without an adapter. It will not fit directly.
  • Buying a cheap walking foot from a seller with no returns. Fit problems show up only after you try it.
  • Starting a seam at full speed on a new foot. Turn the handwheel through a full stitch at the widest setting first.

Good to know

What does universal actually mean on a presser foot listing?

It means the foot fits one shank system, not every machine. A foot labeled universal low shank will not fit a high shank machine, a Singer slant needle machine or a Bernina without an adapter. Treat the word as a hint and read the compatibility line for shank, snap-on type and maximum stitch width.

Where is a generic foot usually fine?

On simple feet with no moving parts: 1/4 inch, zipper, cording, rolled hem, edge stitch and darning feet. They have no moving parts, so fit is the main thing to check. Forum users also report a generic ruffler being good enough for occasional use, even on a Bernina, while saying the original material is better.

Where is the original worth the money?

On a walking foot, a binder, a ruffler or anything you use every week. Many users on a sewing forum report that brand walking feet are better built than cheap copies and can often be adjusted and oiled. Some say a few generics worked close to the original on their machine. For a machine with a proprietary system, such as Bernina, the original also removes fit doubts.

What should you check on a walking foot before buying?

Check shank, maximum stitch width and whether the foot straddles your needle clamp screw. Brother says its SA140 is for forward sewing only, so do not use stitches that move sideways or in reverse. One customer review of a low shank walking foot notes that the automatic needle threader could not be used with the foot attached.

How do you use generic feet on a Bernina?

Use a #75 adapter in the right style. Old style adapters cover machines made roughly between 1954 and 1998, and new style feet carry red numbers on the sticker. A retailer notes that the snap-on shank on entry-level Bernina models only takes the snap-on feet that came with the machine.

FAQ

Are universal presser feet as good as original ones?

For simple feet, often yes. For feet with moving parts, such as a walking foot, many users find the original better made. It depends on the foot and how often you use it.

Will a high shank foot fit a low shank machine?

Not directly. A high shank foot sits too high for a low shank machine, so it will not work. The other way round, a high shank machine can take low shank snap-on feet with a high shank adapter. Screw-on low shank feet do not fit a high shank machine directly.

How do I measure my shank height?

Lower the presser bar with no fabric under it. Measure from the needle plate to the center of the foot screw. About 1/2 inch (13 mm) is low shank and about 1 inch (25 mm) is high shank.

Can a wrong foot damage my machine?

Yes, if the needle hits it. Check the stitch width range in the listing and turn the handwheel by hand through a stitch at your widest setting before sewing.

Do generic feet fit a Bernina?

Yes, with a #75 adapter in old style or new style, depending on your machine. Entry-level snap-on models are an exception. Check your model before buying.

Does the same Brother foot fit every Brother machine?

No. Retailers list some Brother PC and ULT models as needing a low shank adapter for the SA140. Check your model number.

More guides

Sources

Last checked:

WR

About the author: Will Riegger

Editor in charge