☰ Menu
ShankCheck › Guides
Find the right presser foot

Overcast foot for your sewing machine: how to choose the right model

An overcast foot (also sold as overlock foot or overedge foot) lets your machine finish a raw edge with a zigzag or overlock style stitch that wraps the edge without pulling it into a tunnel. It does not trim the fabric like a serger. It only guides the edge and keeps the stitch flat. Which one to buy depends on your shank type, your maximum stitch width and the kind of fabric you sew. This page covers those three points only. For shank basics, see our main presser foot finder. We earn a commiss

Find your match →
Independently researchedSources linkedNo extra cost to you

As an Amazon Associate we earn from qualifying purchases. This does not change your price.

Our picks

Top pick

Brother overcasting foot (low shank snap-on, brand original)

For: Owners of Brother home machines with a snap-on foot who want a foot that is made for their machine.

A brand original is the safest match for stitch width and needle opening. Check your manual for the exact letter of the foot on your model.

Price range: Check the current Amazon price. Brand or

View on AmazonAd

Generic low shank snap-on overcast foot

For: Beginners with a low shank snap-on machine who want a low cost way to finish seam edges on woven fabric.

Works on many standard machines. The listing should say low shank snap-on and the stitch width it supports.

Price range: Usually the budget choice. Check the cur

View on AmazonAd

Low shank screw-on overedge foot

For: Owners of older screw-on machines such as Kenmore, Elna or White.

Fits the standard low shank bar when screwed on. Measure before you buy.

Price range: Check the current Amazon price.

View on AmazonAd

High shank overcast foot

For: Owners of high shank machines, for example Juki TL series or Brother PQ1500S.

A low shank foot will not fit. This foot is made for the high shank bar.

Price range: Check the current Amazon price.

View on AmazonAd

Slant shank overedge foot

For: Owners of Singer 301, 401, 500 series and similar slant shank machines.

Labeled slant shank, so it matches the angled bar. Not interchangeable with low shank.

Price range: Check the current Amazon price.

View on AmazonAd

Snap-on presser foot set with overcast foot

For: Those who also need a zipper foot, a blind hem foot and a few other basics.

Often cheaper than buying single feet. Make sure the set is for your shank type and that the overcast foot is included in the listing.

Price range: Check the current Amazon price.

View on AmazonAd

Common buying mistakes

  • Buying a foot labeled low shank for a high shank or slant shank machine.
  • Ordering a generic foot without checking the maximum stitch width of the machine.
  • Expecting the foot to trim the fabric like a serger.
  • Using a high stitch width without hand turning the wheel for the first stitches. The needle can hit the foot if the foot does not fit.
  • Skipping a test on a scrap of the real fabric, especially on knits and thick fabric.
  • Ignoring the machine manual. It names the right foot letter and the stitch for it.

Good to know

What does an overcast foot do?

It guides the fabric edge while the needle swings in a zigzag or overcast stitch. Many models have a pin or a guide post that the stitch wraps around, or a brush or bar on the foot. The edge stays flat and the stitch does not pull the fabric into a roll. It does not cut. If you want a trimmed edge, cut the allowance first.

Overcast foot or zigzag foot: what is the difference?

A standard zigzag foot works for general zigzag, but the edge can curl or tunnel. An overcast foot has a guide that holds the edge in place and keeps the stitch even. For occasional finishing of woven seams, a zigzag foot may be enough. For frequent edge finishing, an overcast foot is more comfortable.

Which stitch should I use with it?

Use the overcast or zigzag stitch your manual names for that foot. Many machines have a 3 step zigzag, a stretch overlock stitch and a simple overcast stitch. Test on a scrap of your real fabric and adjust stitch length and width.

Does it replace a serger?

No. A serger trims, stitches and wraps in one pass and is faster. An overcast foot is a good low cost option for light finishing, for people who sew now and then and for sewists who want to avoid buying another machine.

How do I know which foot fits my model?

Check the manual or the accessory list of your model first. If you have no manual, check the shank type and the maximum stitch width. When in doubt, use the part number of the foot you already own or search with your brand and model number.

FAQ

Is an overcast foot the same as an overlock foot?

In most shops the terms overcast foot, overlock foot and overedge foot are used for the same type of foot. Brands use their own names and letters, so check the description.

Can I use an overcast foot on knit fabric?

Yes, with a stretch overcast stitch and light pressure. Test on a scrap first. Knits can wave if the feed is too strong or the stitch is too tight.

Will a generic overcast foot fit my Brother machine?

Often yes if your machine is low shank snap-on and the listing names the right shank and width. A Brother original is the safest option. Check your manual.

My machine only sews straight stitches. Can I still use it?

No. An overcast foot needs zigzag or an overcast stitch to work.

Do I need an overcast foot for a Bernina?

Bernina has its own overlock feet for each series. Check your series first. You can also use a generic low shank foot on a Bernina #75 adapter, but make sure you choose old or new style correctly.

More guides