☰ Menu
ShankCheck › Guides
Find the right presser foot

Which presser foot fits my Singer? Find it by model number

Singer made machines with at least three different foot fittings, and the brand name alone does not tell you which one you have. The model number does. Find it on your machine, look it up in the table below, and you will know whether you need a low shank snap-on foot, a low shank screw-on foot or a slant shank foot. We earn a commission when you buy through our links. That does not change what we recommend.

Find your match →
Independently researchedSources linkedNo extra cost to you

As an Amazon Associate we earn from qualifying purchases. This does not change your price.

Singer presser foot finder: four steps

  1. What is the model number?Look for the badge or plate on the front, back or underside of the machine. Numbers like 4423, 9960, 221 or 401A are model numbers. A long serial number on the bed is not. Without a model number, skip to step 3.
  2. Is it a modern snap-on machine or an older screw-on machine?Pull the foot off. If the foot clicks off a shank that stays on the machine, it is a snap-on. If a screw holds the whole foot or a shank to the presser bar, it is a screw-on.
  3. Does the machine look slanted?On a slant shank machine, the needle bar and presser bar tilt toward you instead of standing straight up. Typical for the Singer 301, 401, 500 and 600 series. These only take feet marked slant shank.
  4. What are you buying?A walking foot replaces the ankle or shank and screws to the presser bar, so it must match your shank type exactly. Simple feet such as a 1/4 inch foot or a zipper foot are easier. On snap-on machines you can choose any low shank snap-on foot.

Quick reference

Singer model or familyShank typeWhat to buyWatch out
Heavy Duty 4423, 4411, 4432, 4452Low shank, snap-onLow shank snap-on feet and a low shank snap-on walking footCheck the maximum stitch width of the foot against your machine before sewing
Simple 3232, Tradition 2277, Promise 1409, Start 1304Low shank, snap-onGeneric low shank snap-on feet or a low shank snap-on setEntry level machines work fine with generic feet, but test the needle swing by h
Quantum Stylist 9960, 7258 and similar computerized modelsLow shank, snap-onLow shank snap-on feet. Feet marked for wide stitches if you use decorative stitA foot with a narrow opening can hit the needle on wide zigzag. Turn the handwhe
Featherweight 221 and 222KLow shank, screw-onLow shank screw-on feet made for the FeatherweightThe 221 is straight stitch only. Do not use feet with wide openings for zigzag
Older classics such as 15 class, 201, 66, 99Usually low shank, screw-onLow shank screw-on feet. Confirm with a test fitNot every vintage machine is standard. Measure and compare before buying a walki
301, 401, 403, 500, 503, 600 and 700 Touch & SewSlant shankFeet and walking foot labeled slant shank. A slant snap-on shank lets you use snNothing labeled low or high shank fits these machines
Model number unknown or not listed hereCheck by testOrder one cheap simple foot first, or compare your foot and presser bar with phoDo not buy a walking foot until you have confirmed the shank type

Our picks

Top pick

Low shank snap-on walking foot

For: Owners of Singer Heavy Duty, Simple, Tradition and similar snap-on machines who quilt or sew thick layers

It feeds the top layer with the feed dogs, so layers do not creep. It matches the common modern Singer snap-on fitting. Make sure the listing says it fits your model or low shank snap-on machines.

Price range: Assumption: roughly 15 to 40 USD, check

View on AmazonAd

Slant shank walking foot (Singer 421333 type)

For: Owners of Singer 301, 401, 500, 600 series

The only walking foot type that fits a slant shank machine. Listings should say slant shank clearly.

Price range: Assumption: roughly 15 to 40 USD, check

View on AmazonAd

Slant snap-on shank with feet

For: Slant shank owners who want to change feet quickly

Replaces the screw-on shank so you can use snap-on slant feet. Check that the listing names slant shank.

Price range: Assumption: roughly 10 to 25 USD, check

View on AmazonAd

Low shank snap-on presser foot set

For: Beginners on a modern Singer who want zipper, buttonhole, blind hem and other basics

A set gives you the basic feet at a lower price than buying them separately. Look for sets labeled low shank snap-on.

Price range: Assumption: roughly 15 to 35 USD, check

View on AmazonAd

Featherweight 221 attachments and feet

For: Featherweight 221 and 222K owners

Low shank screw-on feet suit the Featherweight. Choose feet sold for the Featherweight so the opening is right for a straight stitch machine.

Price range: Assumption: roughly 10 to 30 USD, check

View on AmazonAd

1/4 inch quilting foot, low shank snap-on

For: Piecing quilters with a modern Singer

Gives a consistent seam allowance when you do not have a seam guide you trust. It is a low risk first purchase.

Price range: Assumption: roughly 8 to 20 USD, check c

View on AmazonAd

Common buying mistakes

  • Buying by brand only. Singer used low shank snap-on, low shank screw-on and slant shank fittings.
  • Ordering a walking foot before confirming the shank type.
  • Using a low shank foot on a slant shank machine, or the other way around.
  • Mistaking the serial number for the model number.
  • Skipping the handwheel test. Turn the wheel by hand before sewing so the needle does not hit the foot.
  • Buying a wide opening foot for a straight stitch only machine such as the Featherweight 221.

Good to know

Where do I find the model number on my Singer?

Check the nameplate or badge on the front, back or underside. Older machines may only show the model on a small plate near the bed. The serial number is a different number and does not tell you the shank type. If you find no model number, a photo of the machine in a Singer owner group or a search of your serial number on the Singer site can help.

Why do slant shank machines need special feet?

On a slant shank machine the needle and presser bar are tilted. Feet are built for that angle. A low shank foot will sit crooked and may hit the needle plate. That is why only feet marked slant shank fit the 301, 401 and 500 series.

Can I use a walking foot on my Singer?

Yes, if you match the shank type. A walking foot replaces the ankle or shank, so you need the right one for your machine. On modern snap-on Singers, a low shank snap-on walking foot is the usual choice. On slant machines you need a slant shank walking foot. On a Featherweight, check a listing made for it.

Do generic feet fit Singer machines?

Usually yes for low shank snap-on machines. Generic feet are made to the common standard. Read the listing for the shank type, not just the brand name. If the foot comes with a different shank, it may not fit.

What if the foot does not clamp or the needle hits it?

Stop and turn the handwheel by hand. If the needle touches the foot, the opening is too narrow for your stitch width or the shank does not match. Do not force the foot. Return it and check the shank type again.

FAQ

Are all Singer presser feet the same?

No. Singer used low shank snap-on, low shank screw-on and slant shank fittings. The model number tells you which one your machine has.

What shank does the Singer Heavy Duty 4423 use?

It is a low shank snap-on machine. Low shank snap-on feet and a low shank snap-on walking foot are the usual choices.

What shank does the Singer Featherweight 221 use?

It uses a low shank, screw-on foot. It is a straight stitch machine, so use feet made for it.

Which Singers are slant shank?

The Singer 301, 401, 403, 500, 503, 600 and 700 Touch & Sew series are slant shank. Buy feet labeled slant shank.

Can I put snap-on feet on an older screw-on Singer?

Often yes, with a snap-on shank that matches your type. For low shank machines use a low shank snap-on adapter. For slant machines use a slant snap-on shank.

Does a low shank walking foot fit a slant shank Singer?

No. A slant shank machine needs a walking foot labeled slant shank.

My model is not listed. What now?

Compare your foot and presser bar with listing photos, or try a cheap simple foot first. Do not buy a walking foot until you have confirmed the shank type.

More guides