As an Amazon Associate we earn from qualifying purchases. This does not change your price.
Presser foot finder: four questions, one answer
- Does your foot snap on or screw on?Look at the foot holder. If the foot clips onto a small crossbar on the holder (the ankle), it is snap-on. If the foot is held by a screw at the bar, it is screw-on.
- Is your shank low, high or slanted?Lower the presser foot and measure from the screw center to the needle plate. Sources give about 1/2 to 3/4 inch for low and about 1 inch or more for high. A visibly angled bar on a vintage Singer is slant.
- Is it a Bernina?Bernina uses its own mount. You need the #75 adapter in the old or new style, matched to your model, before any generic low shank foot.
- What is your maximum stitch width?Walking feet come in 5 mm and 7 mm versions. Pick the one that matches your machine, and check the model list before you order.
Quick reference
| Your machine | Shank / system | What to buy | Watch out |
|---|---|---|---|
| Current Brother, Baby Lock, Janome, Singer, Juki home machine | Low shank, snap-on holder | Snap-on feet for your brand or universal low shank | Screw-on feet need the snap-on holder removed first |
| Older machine with bare screw-on shank | Low shank, screw-on | Screw-on feet, or low shank snap-on adapter for clip-on feet | Adapter sits between the bar and the foot |
| Pfaff or some Husqvarna Viking models | Low shank, own holder | Often universal snap-on feet plus a low shank snap-on adapter, but this depends on the model | Check your exact model before ordering |
| Sit-down quilting machine or some high-end home machines | High shank | High shank feet, or high shank snap-on adapter | A low shank snap-on adapter will not work here |
| Singer 401, 500 and other slant needle machines | Slant shank | Slant shank feet only | Search with the exact model number |
| Bernina, older models | Bernina old style | #75 adapter, old style, then low shank feet | Old and new style adapters differ |
| Bernina Activa, Artista, Aurora, Virtuosa and later | Bernina new style | #75 adapter, new style, then low shank feet | Some models use other adapters by year |
| Singer Featherweight | Low shank | Low shank screw-on feet | Straight stitch only, so skip wide zigzag feet |
Our picks
Brother SA140 walking foot (7 mm, low shank, screw-on)
It is the original walking foot for 7 mm low shank machines. Some Brother high shank models (such as PC-8500 or the ULT series) need the Adapter S (SA131) as well. Use it for forward sewing only.
View on AmazonAdBrother SA166 walking foot (5 mm, low shank)
SA140 is the 7 mm foot. SA166 is listed for 5 mm machines. Check your model against the seller's fit list.
View on AmazonAdLow shank snap-on adapter (presser foot holder)
It bolts to the low shank bar and lets you use the large range of snap-on feet. It does not work on high shank machines.
View on AmazonAdHigh shank snap-on adapter
Snap-on feet are built for low shank height. This adapter bridges the gap. Do not combine it with a low shank adapter.
View on AmazonAdBernina #75 shank adapter (old style or new style)
It lets a Bernina take screw-on low shank feet. Old and new style are different parts, so match your model. Snap-on feet also need a low shank snap-on adapter on top.
View on AmazonAd
Brother SA185 1/4 inch piecing foot with guide
It gives a consistent quarter inch seam. It is listed as fitting a range of Brother models, so confirm yours first.
View on AmazonAdOur take
We would start with the measurement, not the brand. A snap-on adapter only makes sense if your machine has a bare screw-on bar and you want clip-on feet. Screw-on feet such as walking feet fit that bar directly, so you do not need the adapter for them. For a 7 mm Brother, we would choose the genuine SA140 if the price gap to a generic foot is small, and a generic foot only after checking the model list. On a Bernina, we would pay for the correct #75 adapter first and add other feet later. We have not tested these products ourselves. This page is based on manufacturer and retailer information, listings and user feedback.
What owners report
- Many reviewers say the low shank walking foot (SA140 type) fits and works on their Brother machines. A few say it did not fit the model they ordered it for. One reports that the automatic needle threader could not be used with the foot attached. Source
- Some buyers report receiving the wrong Bernina adapter version. One eBay buyer says the standard low shank version arrived instead of the old style one that was pictured. Source
Common buying mistakes
- Buying by brand name only. Two Brother machines can need different walking feet, depending on stitch width and shank.
- Mixing the low shank snap-on adapter and the high shank adapter. They are not used together.
- Ordering a Bernina adapter without checking old or new style. One eBay buyer reports getting the standard low shank version instead of the old style one.
- Assuming 'fits most machines' means yours. Check the seller's model list.
- Ignoring the stitch width. A 7 mm foot on a 5 mm machine, or the reverse, may not clear the needle or the feed dogs.
- Leaving the snap-on holder on when fitting a screw-on foot.
Good to know
How do I change a snap-on foot?
Raise the presser foot lever. Most holders have a small lever at the back of the ankle. Press it and the foot drops off. Slide the new foot under the holder, a little further forward than you expect, and lower the lever until it clips in. If the foot will not seat, check for lint, a bent crossbar or a missing clip on the holder.
How do I measure shank height?
Lower the presser foot and measure from the center of the foot screw to the needle plate. Wikipedia gives about 1/2 inch (13 mm) for low shank and 1 inch (25 mm) for high shank. Some retailers quote about 3/4 inch for low. The exact figure varies by source, so treat it as a rough guide. Clearly under an inch is low, about an inch or more is high. Values near 3/4 inch are unclear: some retailers count them as low, others list a separate medium shank. Measure twice and check the seller's fit list before ordering.
Can I use a screw-on walking foot on a snap-on machine?
Yes, on most low shank machines. Take off the snap-on holder, then screw the walking foot to the bar. Brother notes that the white plastic arm must sit over the needle bar screw. Walking feet like the SA140 are for forward sewing only. One reviewer on a parts shop page says the automatic needle threader no longer works with the foot attached.
What does a low shank adapter do on a high shank machine?
It adds height so low shank screw-on feet fit. Brother sells it as Adapter S, in set SA131. You can fit low shank feet to a high shank machine this way, but not the other way around. A high shank foot will not fit a low shank bar.
What about Bernina and slant shank machines?
Bernina feet are generally not swappable with other brands. A #75 adapter makes the machine take low shank feet, and a low shank snap-on adapter on top lets you use snap-on feet. Slant shank feet fit slant needle machines such as the Singer 401 and 500, and those machines take no other feet.
FAQ
Will any low shank foot fit any low shank machine?
Mostly yes. Wikipedia says any low shank foot fits any low shank machine. Bernina and some Pfaff and Husqvarna Viking models are exceptions, and with walking feet the stitch width matters too.
Do I need an adapter to use snap-on feet?
Only if your machine has no snap-on holder. Most current home machines already have one. Screw-on machines can take a low shank snap-on adapter.
Can I use a low shank foot on a high shank machine?
Yes, with a low shank adapter. Brother's Adapter S (SA131) does this for its high shank bars. The reverse does not work.
My manual is gone. How do I find my foot type?
Measure the shank, check whether the foot clips or screws on, and search with the exact model number from the nameplate. Use the manufacturer's accessory list when you can.
More guides
- Brother Sewing Machine Presser Foot Compatibility List
- Which presser foot fits my Singer? Find it by model number
- How to check Janome presser foot fit
- Low shank or high shank presser foot: how to tell which one you have
- Which zipper foot fits my sewing machine?
- Which buttonhole foot fits my sewing machine?
- Walking Foot Compatibility by Sewing Machine Model
- Overcast foot for your sewing machine: how to choose the right model
- Snap-on presser foot adapters: what fits which machine
- Screw-on vs snap-on presser feet: what is the difference?
- Which presser foot for leather and denim?
- Original or universal presser foot: which one should you buy?
- Lost a presser foot? How to find the replacement that fits
- Which presser foot fits my Juki?
Sources
- Brother USA: Accessory Spotlight, Low Shank Adapter S
- AllBrands: Brother SA140 Walking Foot
- Sewing Machine Outlet: Brother SA140
- Wikipedia: Presser foot
- MadamSew: Will This Presser Foot Fit My Machine?
- Red Deer Sewing: Presser Foot Guide
- Sewing Bee Fabrics: Sewing Machine Feet Guide
- The Colorful World of Sewing: Bernina #75 Shank Adapters
- Brother SA140 Walking Foot Attachment, Low Shank Screw On up to 7mm Wide - New Low Price! at AllBran
- Brother Walking Foot Sa140
- LNKA Sewing Machine Walking Foot Even Feed Quilt Feet SA140 for Brother
- Brother SA140 XC2214002 Original Genuine Walking Foot Even Feed Attachment, Low Shank Screw On, for
Last checked:
About the author: Will Riegger
Editor in charge