☰ Menu
Find the right presser foot

Which presser foot fits my sewing machine?

You have a sewing machine, maybe an inherited one with no manual, and you want a walking foot, a 1/4 inch foot or a feet set that fits on the first try. Answer four questions, read off your shank type in the table, and you will know which foot to buy and which listings to skip. We earn a commission when you buy through our links. That does not change what we recommend.

Find your match →
Independently researchedSources linkedNo extra cost to youLast checked: 2026-11-18

As an Amazon Associate we earn from qualifying purchases. This does not change your price.

Shank finder: four questions, one answer

  1. 1. Does your foot snap on or screw on?Take the foot off. If it clips onto a separate holder (the ankle) that stays on the presser bar, you have a snap-on system. Then you only need to match the brand of the snap-on holder and the stitch width. If the foot itself is held by one screw, it is a screw-on system and shank height matters. Som
  2. 2. Is the shank low, high or slant?Lower the presser foot lever. Measure from the bed (needle plate) to the center of the screw that holds the foot. Most sources put low shank at about 1/2 inch and high shank at about 1 inch. One retailer guide quotes roughly 3/4 inch and 1 1/4 inches, so the exact numbers depend on where you start m
  3. 3. What is your maximum stitch width?A foot has to be wide enough for the needle to swing without hitting it. Brother's SA140 walking foot is sold for machines up to 7 mm zigzag width, and Brother makes a separate version for 5 mm machines. Set the widest zigzag, turn the handwheel by hand and watch that the needle clears the foot befo
  4. 4. Is it a Bernina or an unusual brand?Bernina feet do not take generic low shank feet directly. You need a #75 adapter, and it comes in an old style (feet made 1954 to 1998) and a new style. Check which one your machine takes before you order. Singer Featherweights use low shank feet. Slant shank feet are made for slant needle machines such as the Singer 401A. Check your model before you order.

Quick reference

Your machineShank / systemWhat to buyWatch out
Most current Brother, Baby Lock, Janome, Singer, Kenmore home machines with screLow shankAny low shank foot rated for your stitch widthCheck max stitch width: 5 mm and 7 mm versions exist
Machine with snap-on holder, current Brother or Janome home modelSnap-on, low shank heightSnap-on feet for your brand, or low shank adapter plus generic snap-on feetSome Brother PC and ULT models may need a low shank adapter for the SA140
Straight stitch quilting machine, some high-end home and industrial machinesHigh shankHigh shank feet, or a high shank snap-on adapter for snap-on feetHigh shank feet are needed. A low shank foot will not fit directly. A high shank machine can take low shank feet only with a low shank adapter
Singer 401A, 500A, 600 Touch & Sew and other slant needle machinesSlant shankSlant shank feet onlySearch with your exact model number
Bernina old style (before the 1998 foot change)Bernina old style#75 adapter, old style, then low shank feetOld and new style adapters are not interchangeable
Bernina new style (Activa, Artista, Aurora and later)Bernina new style#75 adapter, new style, then low shank feetNew style feet have red numbers. Confirm with your model before ordering
Singer FeatherweightLow shankLow shank screw-on feetWide zigzag feet are not needed, the machine is straight stitch only

Our picks

Top pick
Brother SA140 walking foot (7 mm, low shank)
Illustration

Brother SA140 walking foot (7 mm, low shank)

For: Owners of Brother, Baby Lock and other low shank screw-on machines up to 7 mm stitch width who quilt or sew several laye

The genuine part is sold for 7 mm zigzag machines and listed with a long run of Brother models, plus some Singer, Kenmore and Viking models. One retailer notes that some Brother PC and ULT models need a low shank adapter. Check your model on the seller's list before you order.

Price range: 10-80 USD (generic copies at the low end

View on AmazonAd
High shank walking foot XA7253001 (original or equivalent)
Illustration

High shank walking foot XA7253001 (original or equivalent)

For: Quilters with a high shank straight stitch machine such as the Brother PQ1500S, Juki TL-2010Q or Janome 1600P

A low shank walking foot will not fit these machines. Confirm the part number against your manual or the seller's model list, because we could not verify the full compatibility list.

Price range: 20-60 USD (estimate)

View on AmazonAd
Low shank snap-on adapter (ankle)
Illustration

Low shank snap-on adapter (ankle)

For: Owners of low shank screw-on machines who want to use snap-on feet

It screws onto the presser bar and lets you clip on standard snap-on feet. Many feet sets already include one.

Price range: 5-15 USD (estimate)

View on AmazonAd

Slant shank walking foot (Singer 421333 type)

For: Owners of vintage Singer slant needle machines such as the 401A, 500A or 600 Touch & Sew

Slant shank feet are made for Singer slant needle machines, and those machines generally do not take straight shank feet. Buy only from listings that name your model number. We did not verify the part number, so confirm it with the seller.

Price range: 20-50 USD (estimate)

View on AmazonAd

Bernina #75 low shank adapter (old style or new style)

For: Bernina owners who want generic low shank feet, such as a walking foot or 1/4 inch foot

It attaches to the presser bar so standard screw-on low shank feet fit. Old style and new style are different parts. Sellers sometimes mix up the two versions, so check the photo and part number: 0019477000 is listed as old style, 0083677000

Price range: 8-27 USD (generic about 8 to 15, genuine

View on AmazonAd

1/4 inch piecing foot with guide (Brother SA185 or low shank equivalent)

For: Quilters piecing blocks on a Brother or other low shank snap-on machine

The guide keeps a consistent 1/4 inch seam. The genuine SA185 is a snap-on foot with a model list from Brother, and it is listed for use with some Juki F-series machines too. Test the seam on scrap fabric, because needle position and foot width differ between machines.

Price range: 5-25 USD (estimate)

View on AmazonAd

Low shank snap-on presser foot set

For: Beginners and owners of used machines who want zipper, rolled hem, blind hem and cording feet in one purchase

One adapter and many feet are cheaper than buying them one by one. Check the stitch width the set is made for and make sure the adapter is included.

Price range: 15-50 USD (estimate)

View on AmazonAd

Our take

Work out your shank type first, then pick the foot. For a current low shank machine with a stitch width up to 7 mm, we would look at the Brother SA140 or a well reviewed copy, but only after checking the model list. A Bernina needs the right #75 adapter. Singer slant needle machines need slant shank feet. A large set pays off only if an adapter is included and you will use several of the feet. We have not tested these feet ourselves. This page rests on manufacturer details, retailer lists and sewing guides.

Common buying mistakes

  • Buying by brand name instead of shank and system. A foot listed for Brother can fit a Janome with the same shank, and a foot listed for your brand can still be wrong if your model uses a different holder.
  • Trusting 'fits all low shank machines' in a title without reading the model list or the stated stitch width.
  • Ordering a low shank walking foot for a high shank quilting machine, or the reverse.
  • Mixing up Bernina old style and new style #75 adapters.
  • Buying a slant shank foot for a straight low shank Singer, or a low shank foot for a vintage slant machine.
  • Skipping the handwheel test at the widest zigzag. A needle that hits the foot can break the needle and damage the foot.

Good to know

How do I measure my shank when sources give different numbers?

Most references say low shank is about 1/2 inch (13 mm) from the bed to the center of the foot screw, and high shank is about 1 inch (25 mm). One retailer guide gives about 3/4 inch and 1 1/4 inches instead. The gap comes from where people put the ruler. So do not rely on one number. Measure with the foot lowered, note whether the screw sits straight or at an angle, and compare with a foot you already own. If your reading is about half that of a high shank foot you know, yours is low shank. Then confirm with the accessory chart in the manual or the model list on the foot you plan to buy.

Why does a wrong-shank foot cause stitch problems?

The shank sets the height of the foot above the throat plate. A foot that sits too high can let the fabric flutter and cause skipped stitches. A foot that sits too low can drag the fabric against the feed dogs. If stitch problems began right after you fitted a new foot, check the foot first.

Can I use low shank feet on a high shank machine?

Yes, with a low shank adapter, which turns a high shank machine into a low shank one. It does not work the other way round. A low shank walking foot cannot be used on a high shank machine without that adapter. For snap-on feet on a high shank machine, use a high shank snap-on adapter instead.

What changes for walking feet and 1/4 inch feet specifically?

Walking feet are bulkier and tied to the machine's stitch width and, on some machines, to the presser bar and needle clamp position. Brother lists its SA140 for 7 mm machines and sells a separate version for 5 mm machines. A 1/4 inch foot has a guide blade and needs a straight stitch with the needle in the position the foot was made for. Sew a test seam on scrap fabric and measure it before you cut quilt pieces.

What do I do with a Bernina?

Bernina feet are proprietary, so generic low shank feet only fit through a #75 adapter. Two versions exist: old style for older machines and new style for later ones. Many new style feet carry red numbers. Check this against your manual or the seller's photo, because worn or aftermarket feet may differ. If you inherited a machine, look at the foot numbers and the model on the plate, then match the adapter. Test the widest zigzag by hand before you sew, because a generic foot may be narrower than your machine's maximum width.

What others say

Compatible with All Low Shank Sewing Machines.
Amazon Best Sellers: Best Sewing Machine Presser Feet

Our view: This is a seller's claim in a listing title, and it is too broad. Low shank covers the foot height only. It says nothing about stitch width, snap-on versus screw-on, or Bernina, which needs a #75 adapter first. Treat 'all' as 'most' and check your model.

Fits Select Brother, Singer & Janome Low Shank Models
Amazon Best Sellers: Best Sewing Machine Presser Feet

Our view: The word 'select' is the honest part. It means a model list exists and your machine may not be on it. The bestseller page ranks by sales and does not tell you how to find your shank type. That is the part this page covers.

FAQ

How do I know if my machine is snap-on or screw-on?

Remove the foot. If it clips off a holder that stays on the presser bar, it is snap-on. If one screw holds the foot to the presser bar, it is screw-on.

Will a low shank walking foot fit my Brother?

Often yes, if the machine is a low shank screw-on type up to 7 mm stitch width. Check the model on the seller's or Brother's list, because some PC and ULT models may need a low shank adapter.

Does a Janome or Singer take Brother feet?

Frequently, if both use the same low shank screw-on system or the same snap-on holder. Sellers list Singer, Janome, Baby Lock and Kenmore models for the SA140 type feet, but 'select' models only. Confirm yours.

Is a Singer Featherweight low shank?

Yes. A retailer guide lists all Featherweights as low shank, so low shank screw-on feet fit.

Do I need an adapter for my Bernina?

For generic low shank feet, yes. You need the #75 adapter in the right style, old or new.

Are cheap generic feet worth it?

For simple feet such as a zipper foot or a 1/4 inch foot, we think so, if shank and width match. For a walking foot, compare the model list and read the return policy. Genuine Brother and Singer feet cost more but come with a clear compatibility list.

More guides

Sources

Last checked: